1/12/2024 0 Comments Led light table arduino![]() Place Slave 1 upside down and then disconnect the following sections from the bottom using the LEGO removal tool.ĩ.) Take a White 30cm Bit Light and thread the connector side of the cable through the front hole of the grey brick. Turn ‘ON’ to verify all is working OK.Ĩ.) Disconnect the AA Battery Pack from the expansion board and then turn Slave 1 over and disconnect the following section. Take this time to test the lights we have installed so far by inserting 3x AA Batteries to the AA Battery Pack and then connect the battery pack cable to a spare port on the expansion board. Take a 8-Port Expansion Board and connect all three cables to it. Place the Bit Light in between the following studs and then secure it in place by connecting a provided LEGO Trans Clear Round Plate 1×1 over the top.īring back Boba Fett’s seat and then reconnect Slave 1 back to it’s stand in upright position.ħ.) Pull the cable from the White Bit Light down the right side so that it is together with the two Flashing Red Bit Light cables. Take the cable from the left Flashing Red Bit Light and then thread it through the middle and pull it out from the right side so that both cables are togetherĦ.) Remove Slave 1 from the stand and then place it down.īring Boba Fett’s seat forward and then take a White 30cm Bit Light and thread the connector side down behind his seat. Lay the cable in between studs of the outside and then reconnect the middle part of the right section.įrom the inside of Slave 1, push the Flashing Red Bit Light toward the inside of the hole.ģ.) Thread the connector side of the cable down behind the side of the ship and then reconnect sections of the right side which we removed earlier.Ĥ.) Repeat previous steps to install another Flashing Red 30cm Bit Light to the left side of the cockpit.ĥ.) Remove the middle and the left and right side sections of Slave 1 as per below: ![]() Pull the cable out slightly from the inside as per below: ![]() Thread the Bit Light through the upper hole on the right side of cockpit. You can either place them directly on top of LEGO® studs or in between.ġ.) Start by disconnecting the front window section as well as sections from the right side using the LEGO removal tool as per below:Ģ.) Take a Flashing Red 30cm Bit Light and bend the component part slightly on a 90 degree angle so that it is facing upward. When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). Installing Bit Lights under LEGO® bricks and plates. Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected. If a plug won’t fit easily into a port connector, do not force it. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. Take extra care when inserting connectors to ports of Expansion Boards. Connecting cable connectors to Expansion Boards Do NOT forcefully join LEGO® together around cables instead ensure they are laying comfortably in between each stud.ĬAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light. Important things to note: Laying cables in between and underneath bricksĬables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. If you are wishing to purchase the Light My Bricks LEGO Star Wars Slave 1 (75060) LED light kit , please click here to view the product page Please note: This page lists instructions for the LED light kit only. To download this instructions guide in PDF format please click here. If you run into any issues, please refer to the online troubleshooting guide. To ensure a trouble-free installation of your light kit, please read and follow each step carefully. ![]() Once you have the LED and current limiting resistor connected to your Arudino, upload the code below to the Arduino.The following page is the instructions for the Light My Bricks LEGO Star Wars Slave 1 (75060) LED light kit. The value of the current limiting resistor can be anything from about 200 Ohms up to about 1K Ohms.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |